Introduction The Toyota 1NZ-FE is a 1.5-liter inline-4 engine featuring VVT-i (Variable Valve Timing - intelligence). Its engine management is handled by a sophisticated ECU (Engine Control Unit), typically manufactured by Denso. Understanding the 1NZ ECU pinout is essential for diagnostics, wiring repairs, standalone ECU swaps, turbo conversions, or installing piggyback systems (e.g., GReddy e-Manage).
Terminal Voltage Reference Table (Engine Idling, Warm) | Signal | Pin | Voltage | Condition | |--------|-----|---------|------------| | +B | E5-1 | 13.5–14.5V | Engine running | | VTA | E6-14 | 0.45–0.55V | Closed throttle | | VTA | E6-14 | 3.5–4.5V | WOT | | VG (MAF) | E6-16 | 1.0–1.4V | Idle, warm | | VG (MAF) | E6-16 | 2.0–2.5V | 2500 RPM, no load | | THW | E6-17 | 0.5–0.9V | Engine warm (80-90°C) | | KNK | E6-19 | 0V (DC) | Idle – AC signal present | | VVTP | E6-22 | 7–9V (average) | Duty cycle ~30-40% at idle | | NE+ to NE- | E6-23/24 | AC 2–4V | Cranking – frequency varies | Conclusion The 1NZ-FE ECU pinout is a roadmap for anyone working on Toyota’s reliable 1.5L engine. While the three connectors contain over 70 pins, the critical paths for power, ground, ignition, injection, and primary sensors are straightforward once mapped. 1nz ecu pinout diagram
| Pin | Connector | Wire Color | Signal Name | I/O | Description | |-----|-----------|------------|----------------|-----|-----------------------------| | 1 | E5 (A) | White/Red | +B1 | P | ECU main relay power (12V) | | 2 | E5 (A) | Black/White | +B | P | ECU main relay power (12V) | | 3 | E5 (A) | Brown | E01 | G | Power ground (injectors/ignition) | | 4 | E5 (A) | Brown/Black | E02 | G | Power ground (injectors/ignition) | | 5 | E5 (A) | Black | E1 | G | Sensor ground (ECU internal) | | 6 | E5 (A) | Yellow | IGT1 | O | Ignition trigger – Cylinder 1 | | 7 | E5 (A) | Yellow/Black | IGT2 | O | Ignition trigger – Cylinder 2 | | 8 | E5 (A) | Yellow/Red | IGT3 | O | Ignition trigger – Cylinder 3 | | 9 | E5 (A) | Yellow/Blue | IGT4 | O | Ignition trigger – Cylinder 4 | | 10 | E5 (A) | Red/Blue | #10 | O | Injector driver – Cyl 1 & 2 | | 11 | E5 (A) | Red | #20 | O | Injector driver – Cyl 3 & 4 | | 12 | E5 (A) | Black/Orange | MREL | O | Main relay control | | 13 | E5 (A) | Green/Red | FC | O | Fuel pump relay control | | 14 | E6 (B) | Red/Black | VTA | I | TPS – Throttle position signal | | 15 | E6 (B) | Blue/Red | VTA2 | I | TPS – Sub-throttle (ETCS-i) | | 16 | E6 (B) | Light Green | VG | I | MAF sensor signal | | 17 | E6 (B) | Blue/Yellow | THW | I | ECT – Engine coolant temp | | 18 | E6 (B) | Brown/Yellow | THA | I | IAT – Intake air temp | | 19 | E6 (B) | Pink | KNK | I | Knock sensor signal | | 20 | E6 (B) | Violet | OX1B | I | Front A/F sensor (wideband) | | 21 | E6 (B) | White | OX2B | I | Rear O2 sensor (narrowband) | | 22 | E6 (B) | Blue/Orange | VVTP | O | VVT-i oil control valve | | 23 | E6 (B) | Gray | NE+ | I | Crankshaft position sensor (+) | | 24 | E6 (B) | Gray/Black | NE- | I | Crank sensor (-) | | 25 | E6 (B) | Blue | G2+ | I | Camshaft position sensor | | 26 | E7 (C) | Green/White | SPD | I | Vehicle speed sensor | | 27 | E7 (C) | Silver/Black | SIL | COM | Diagnostic (K-Line) | | 28 | E7 (C) | Violet/White | TC | COM | Diagnostic request (check engine) | | 29 | E7 (C) | Red/White | IMO | COM | Immobilizer transponder coil | | 30 | E7 (C) | Green/Yellow | STA | I | Starter signal | Introduction The Toyota 1NZ-FE is a 1